Pair of Small Crown Dies

Great for detail work in small stock or fine details in large stock. Used to great advantage for power hammer detailing. These act like the pein of your hand hammer, you are able to control the movement of metal in any direction. The critical radii on these dies are CNC machined and then carefully hand dressed by professionals. 2.5" (63.5mm) long.

Pair of Standard Flat Dies

Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Untempered Power Hammer Standard Flat Dies

The Beveling Set

These 5" (127mm) sloped surface dies will quickly produce bevelled edges on any size stock. Great for hinges, rails, flinch plates. . . Two different slopes, 1 : 5 and 1 : 3.33, for low sharp or high steep bevels. The Beveling set comes with our standard radius side die for the bottom. You may order the top Beveling die alone for $310. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Knife Forging Dies

These subtle and elegant dies are specifically designed for bladesmithing by leaders in the knifemaking community. These dies are lightly crowned in all direction, facilitating the crisp multidirectional tapering required to form a blade. Three sides have a ¼” radius and one side has a 1/8” radius allowing you to form shoulders. The smith can even offset the dies to set the tang of the knife to one side with an inner fillet. All done under the hammer. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long. 1-3/4” (44.45mm) wide. Standard length and width. You can check these dies out in action on our YouTube channel.

Pair of Radius Side Dies

Dimensions are 5"(127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Aggressive Drawing Dies

Very aggressive for isolation, fast drawing, sculptural work with heavy forged texture and features. These are similar to the narrow side of the combination dies but will fit much larger work. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Aggressive Fuller Texturing Dies

These 5" (127mm) long texturing dies will quickly fuller or texture up to 5" (127mm) wide stock. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Standard Crown Dies

Crown Dies are used to great advantage for free hand sculptural work. These act like the pein of your hand hammer, you are able to control the movement of metal in any direction. The crown dies and the combo dies are a must have for the artist blacksmith. The critical radii on these dies are CNC machined and then carefully hand dressed by professionals that use these dies daily. 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Full Radius Fullering Dies

An old standard used for fullering, heavy drawing and texturing, sculptural work with heavy forged texture and features. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long. 1.25" (32mm) Primary Radius

Pair of Large Crown Power Hammer Dies

Big BLU Combo Die

Dimensions are 5"(127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Multi Peening + Radius Dies

Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Single Peening + Radius Side Power Hammer Dies

Pair of Single Peening Dies

These 5" (127mm) semispherical texturing dies will quickly produce hammered texturing on any size stock. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Large Flat Dies

The dimensions are 2.5" wide, 5" long, 3" tall.

Pair of Untempered Power Hammer Large Flat Dies

Reverse Radius + Full Radius Power Hammer Dies

These 5" (127mm) long mated curved surface dies will quickly produce cupped rail or other curved shapes. By rotating the work on the long axis you can form larger curved widths. The shape of these dies are CNC machined and then carefully hand dressed by professionals. Bottom die is 2.75" (70mm) wide. Top radius = 1.25" (32mm)

Pair of Bark Texturing Dies

These 5" (127mm) long bark texturing dies will quickly produce bark or vine texturing on 1/2" (13mm) through 2" (49mm) diameter stock. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Multi Peening Dies

Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Pair of Large Drawing Power Hammer Dies

Pair of Platform Dies

Top and Bottom Super Flat Power Hammer Dies

Untempered Top and Bottom Super Flat Power Hammer Dies

Untempered Top and Bottom Super Flat Power Hammer Dies

The Small Bowl Dies Set

These 6" top bowl die (with bottom concave die) are the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.

The Large Bowl Dies Set

These 10" top bowl die (with bottom concave die) are the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.

The Full Bowl Dies Set

These Full 6" & 10" top bowl dies (with bottom concave die) are the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.